| Ground Clearance | 49.8in |
|---|---|
| Blade Capacity - Sae J1265 | 16.11yd3 |
| Digging Depth | 25.4in |
| Height | 4.41ft in |
| Maximum Tilt | 30.9in |
| Note (1) | *Capacities calculated with a trash rack installed. |
| Note (2) | **Weight includes cylinder mounting, lift cylinder and lines, blade, push arms, trunnions, and cylinder lines (Tilt). |
| Blade | 7S LGP |
| Width - Over End Bits | 14.91ft in |
| Displacement | 567cu in |
| Bore | 4.5in |
| Stroke | 5.9in |
| Net Power - Iso 9249 | 235hp |
| Net Power - Sae J1349 | 235hp |
| Gross Power - Sae J1995 | 259hp |
| Engine Model | Cat C9.3 ACERT |
| Flywheel Power | 235hp |
| Gross Power - Iso 14396 | 256hp |
| Net Power - Iso 9249 (Din) | 238hp |
| Global Emissions | U.S. EPA Tier 4 Interim/EU Stage IIIB/Japan MLIT Step 4 |
| Gross Power - Iso 14396 (Din) | 260hp |
| Drive Train Type | Electric Drive |
| Operating Weight | 68600lb |
| Operating Weight - Lgp Wha | 68600lb |
| Shipping Weight - Lgp Wha | 58900lb |
| Cooling System | 22.5gal |
| Fuel Tank | 108gal |
| Engine Crankcase | 8gal |
| Power Train | 16gal |
| Pivot Shaft Compartment | 1.8gal |
| Final Drive - Each - Lgp | 9gal |
| Brakes | ISO 10265 2008 |
| Rops/Fops | ROPS meets criteria ISO 3471:1994, 2008 FOPS meets ISO 3449:1992, 2005 Level II |
| Cab | ANSI/SAE J1166 OCT 98 |
| Pressure Setting - Steering | 4000 psi |
| Bulldozer | 4000 psi |
| Tilt Cylinder | 4000 psi |
| Ripper - Pitch | 4000 psi |
| Ripper - Lift | 4000 psi |
| Steering | 5950 psi |
| Lift Cylinder Flow | 42 gal/min |
| Ripper Cylinder Flow | 42 gal/min |
| Pump Output - Steering | 82.4 gal/min |
| Pump Output - Implement | 52.8 gal/min |
| Pump Type | Piston, variable displacement |
| Maximum Penetration Force | 19639lb |
| Pry-Out Force | 52695lb |
| Overall Beam Width | 82.2in |
| Beam Cross Section | 14in |
| Weight - With One Shank | 3572lb |
| Weight - Each Additional Shank | 330lb |
| Ramp Angle | 26degrees |
| Pocket Spacing | 35.4in |
| Shank Gauge | 70.9in |
| Shank Section | 72 mm 228 mm (2.8 in 9.0 in) |
| Rippers Type | Multi-Shank |
| Number Of Pockets | 3 |
| Maximum Penetration | 25.6in |
| Weight | 3350lb |
| Drum Capacity - 24 Mm (1 In) | 203ft in |
| Drum Capacity - 29 Mm (1.13 In) | 185ft in |
| Oil Capacity | 3.2gal |
| Winch Model | PA90 |
| Increased Tractor Length - Lgp | 93.9in |
| Drum Diameter | 12.5in |
| Winch Drive | Hydraulic |
| Maximum Bare Drum - Line Pull | 90000lb |
| Maximum Full Drum - Line Pull | 57000lb |
| Maximum Bare Drum - Line Speed | 70 ft/min |
| Maximum Full Drum - Line Speed | 116 ft/min |
| Note | *Basic winch weight, mounting arrangement, hydraulic and electrical system weight. |
