| Overall Length | 30.88ft in |
|---|---|
| Width Over Tires | 9.16ft in |
| Wheelbase | 21.5ft in |
| Rear Ground Clearance | 1.26ft in |
| Tandem Axle Wheelbase | 5.42ft in |
| Blade Base | 9.33ft in |
| Height - Top Of Cylinders | 112.4in |
| Height To Top Of Isomount Cab | 11.6ft in |
| Length - Between Tandem Axles | 65in |
| Height - Top Of Cab | 11.6ft in |
| Height - Front Axle Center | 25.2in |
| Height - Exhaust Stack | 128.2in |
| Width - Outside Front Tires | 109.9in |
| Width - Outside Rear Tires | 109.9in |
| Width - Tire Center Lines | 93in |
| Ground Clearance - Rear Axle | 15.1in |
| Pry-Out Force | 28146lb |
| Ripping Depth - Maximum | 15.8in |
| Ripper Shank Holders | 7 |
| Penetration Force | 27222lb |
| Shank Holder Spacing - Minimum | 15in |
| Shank Holder Spacing - Maximum | 19in |
| Number Of Cylinders | 6 |
| Net Power Gear 4-6 | 274hp |
| Engine Make | 2236 |
| Front Frame Structure - Height | 1.4ft in |
| Front Frame Structure - Width | 1ft in |
| Net Power Gear 1-2 | 259hp |
| Power Measured @ | 1800rpm |
| Net Power Gear 5-6 | 274hp |
| Max Power | 274hp |
| Net Power Gears 7-8 | 274hp |
| Displacement | 677cu in |
| Bore | 5.1in |
| Stroke | 5.5in |
| Engine Model | Cat C11 ACERT VHP |
| Derating Altitude | 13000ft in |
| Maximum Torque | 1049lb ft |
| Base Power (1st Gear) - Net | 259hp |
| Speed At Rated Power | 1800 RPM |
| High - Ambient Capability | 122degrees |
| Vhp Plus Range - Net | 193-219 kW (259-294 hp) |
| Vhp Plus Range - Net - Metric | 193-221 kW (262-301 hp) |
| Circle - Diameter | 71.8in |
| Drawbar - Height | 8in |
| Front Axle - Height To Center | 25.2in |
| Circle - Blade Beam Thickness | 2in |
| Drawbar - Width | 3in |
| Base Power (All Gears) - Net | 259hp |
| Standard - Fan Speed - Maximum | 1450 RPM |
| Standard - Fan Speed - Minimum | 550 RPM |
| Standard - Ambient Capability | 109degrees |
| Vhp Range - Net - Metric | 193-205 kW (262-279 hp) |
| Vhp Range - Net | 193-204 kW (259-274 hp) |
| Maximum Torque - Vhp Plus - Net | 1049lb ft |
| Vhp - Gears 4-8, Net | 273.6hp |
| Std Operation Weight - Total | 47133lb |
| Max Operation Weight - Total | 65998lb |
| Cooling System Fluid Capacity | 12.3gal |
| Transmission Fluid Capacity | 23.5gal |
| Circle Gearbox Fluid Capacity | 1.6gal |
| Brakes - Parking | Spring applied, hydraulically released |
| Brakes - Service | Oil-actuated, oil-disc |
| Transmission | Direct drive, power shift, countershaft |
| Forward/Reverse Gears | 8 Fwd/6 Rev |
| Brakes - Secondary | Oil-actuated, oil-disc |
| Brakes - Service - Surface Area | 5347in2 |
| Articulation Angle | 20degrees |
| Turning Radius | 25.9ft in |
| Transmission Type | direct drive, power shift, countershaft |
| Number Of Gears - Forward | 8 |
| Number Of Gears - Reverse | 6 |
| Max Speed - Forward | 31mph |
| Max Speed - Reverse | 24.5mph |
| Wheel Lean | 17.1degrees |
| Oscillation - Total | 32degrees |
| Standby Pressure | 450 psi |
| Maximum System Pressure | 3500 psi |
| Max Depth Of Cut | 17.3in |
| Side Shift Left | 29.1in |
| Side Shift Right | 31.1in |
| Blade Pull At Max Weight | 39678lb |
| Blade Down Pressure | 38666.9lb |
| Pump Type | Variable Displacement |
| Pump Flow | 74gal/min |
| Relief Valve Pressure | 3500psi |
| Circuit Type | Electro-hydraulic load sensing, closed center |
| Pump Output | 74 gal/min |
| Blade Width | 14ft in |
| Arc Radius | 16.3in |
| Throat Clearance | 4.6in |
| Cutting Edge Width | 8in |
| Cutting Edge Thickness | 0.6in |
| End Bit - Width | 6in |
| End Bit - Thickness | 0.6in |
| Moldboard Height | 27in |
| Moldboard Thickness | 1in |
| Moldboard Width | 14ft in |
| Blade Pull - Maximum Gvw | 39619lb |
| Blade Pull - Base Gvw | 30829lb |
| Blade Down Pressure - Base Gvw | 22130lb |
| Blade Pull - Base | 31123lb |
| Blade Pull - Maximum | 40460lb |
| Down Pressure - Base | 22318lb |
| Down Pressure - Maximum | 36734lb |
| Diameter | 71.8in |
| Shift Left | 25.5in |
| Shift Right | 20.5in |
| Max Reach Outside Tires - Left | 85.4in |
| Max Reach Outside Tires - Right | 89.7in |
| Max Lift Above Ground | 16.5in |
| Blade Tip Angle - Front | 40degrees |
| Blade Tip Angle - Rear | 5degrees |
| Top Speed - Forward | 31mph |
| Top Speed - Reverse | 24.5mph |
| Steering Range - Left/Right | 47.5 degrees |
| Articulation Angle - Left/Right | 20 degrees |
| Forward - 8th | 31mph |
| Forward - 7th | 21.3mph |
| Forward - 6th | 15.4mph |
| Forward - 5th | 11.4mph |
| Forward - 4th | 7.3mph |
| Forward - 3rd | 5.3mph |
| Forward - 2nd | 3.7mph |
| Forward - 1st | 2.7mph |
| Reverse - 6th | 24.5mph |
| Reverse - 5th | 16.9mph |
| Reverse - 4th | 9mph |
| Reverse - 3rd | 5.8mph |
| Reverse - 2nd | 4mph |
| Reverse - 1st | 2.1mph |
| Brakes | ISO 3450 |
| Rops/Fops | ISO 3471 / ISO 3499 |
| Sound | ISO 6394/ISO 6395 |
| Steering | ISO 5010:1992 |
| Cooling System | 12.3gal |
| Engine Oil | 7.9gal |
| Hydraulic System Tank | 15.9gal |
| Tandem Housing - Each | 25.5gal |
| Circle Drive Housing | 1.6gal |
| Fuel Capacity | 130gal |
| Circle Centershift - Right | 20.5in |
| Circle Centershift - Left | 25.5in |
| Moldboard Sideshift - Right | 31.1in |
| Moldboard Sideshift - Left | 29.1in |
| Blade Tip Range Forward | 40 degrees |
| Blade Tip Range Backward | 5 degrees |
| Maximum Lift Above Ground | 16.5in |
| Maximum Depth Of Cut | 17.3in |
| Maximum Blade Position Angle | 65 degrees |
| Height | 24.3in |
| Width | 8.4in |
| Sidewall Thickness - Inner | 0.8in |
| Sidewall Thickness - Outer | 0.8in |
| Drive Chain Pitch | 2.3in |
| Wheel Axle Spacing | 65in |
| Tandem Oscillation - Front Up | 15 degrees |
| Tandem Oscillation - Front Down | 25 degrees |
| Gear - Forward 5th | 275hp |
| Gear - Forward 1st | 259hp |
| Gear - Forward 2nd | 265hp |
| Gear - Forward 3rd | 270hp |
| Gear - Forward 4th | 275hp |
| Gear - Forward 6th | 275hp |
| Gear - Forward 7th | 275hp |
| Gear - Forward 8th | 275hp |
| Gear - Reverse 1st | 259hp |
| Gear - Reverse 2nd | 265hp |
| Gear - Reverse 3rd-6th | 270hp |
