| Overall Length | 27.85ft in |
|---|---|
| Width Over Tires | 8.14ft in |
| Wheelbase | 19.4ft in |
| Rear Ground Clearance | 1.13ft in |
| Tandem Axle Wheelbase | 4.96ft in |
| Front Ground Clearance | 1.87ft in |
| Blade Base | 8.24ft in |
| Height To Top Of Isomount Cab | 10.75ft in |
| Length - Between Tandem Axles | 59.5in |
| Height - Top Of Cylinders | 113.7in |
| Height - Top Of Cab | 10.75ft in |
| Height - Front Axle Center | 22.5in |
| Height - Exhaust Stack | 112.4in |
| Width - Outside Front Tires | 97.7in |
| Width - Outside Rear Tires | 97.7in |
| Width - Tire Center Lines | 84.1in |
| Ground Clearance - Rear Axle | 13.6in |
| Pry-Out Force | 25972lb |
| Penetration Force | 18911lb |
| Number Of Cylinders | 6 |
| Net Power Gear 4-6 | 173hp |
| Engine Make | 2236 |
| Front Frame Structure - Height | 0.9ft in |
| Front Frame Structure - Width | 0.9ft in |
| Net Power Gear 1-2 | 163hp |
| Power Measured @ | 2000rpm |
| Net Power Gear 5-6 | 173hp |
| Max Power | 173hp |
| Net Power Gears 7-8 | 173hp |
| Displacement | 403cu in |
| Bore | 4.2in |
| Stroke | 5in |
| Engine Model | Cat C6.6 ACERT VHP |
| Derating Altitude | 11500ft in |
| Maximum Torque | 690lb ft |
| Base Power (1st Gear) - Net | 158hp |
| Speed At Rated Power | 2000 RPM |
| High - Ambient Capability | 122degrees |
| Vhp Plus Range - Net | 118-144 kW (158-193 hp) |
| Circle - Diameter | 60.2in |
| Drawbar - Height | 6in |
| Front Axle - Height To Center | 22.5in |
| Circle - Blade Beam Thickness | 1.4in |
| Drawbar - Thickness | 0.4in |
| Drawbar - Width | 3in |
| Torque Rise - Vhp Plus | 40% |
| Base Power (All Gears) - Net | 158hp |
| Standard - Fan Speed - Maximum | 1,150 rpm |
| Standard - Fan Speed - Minimum | 550 RPM |
| Standard - Ambient Capability | 109degrees |
| Vhp Range - Net | 118 -129 kW (158-173 hp) |
| Drawbar - Yoke Bar Thickness | 0.8in |
| Std Operation Weight - Total | 32016lb |
| Max Operation Weight - Total | 44690lb |
| Cooling System Fluid Capacity | 10.4gal |
| Circle Gearbox Fluid Capacity | 1.8gal |
| Brakes - Parking | Multiple Oil Disc |
| Brakes - Service | Multiple Oil Disc |
| Transmission | Direct drive, power shift, countershaft |
| Forward/Reverse Gears | 8 Fwd/6 Rev |
| Brakes - Secondary | Dual circuit control system |
| Brakes - Service - Surface Area | 3565in2 |
| Articulation Angle | 20degrees |
| Turning Radius | 24.5ft in |
| Transmission Type | direct drive, power shift, countershaft |
| Number Of Gears - Forward | 8 |
| Number Of Gears - Reverse | 6 |
| Max Speed - Forward | 27.7mph |
| Max Speed - Reverse | 23.5mph |
| Wheel Lean | 18degrees |
| Oscillation - Total | 32degrees |
| Ground Clearance | 1.9ft in |
| Standby Pressure | 450 psi |
| Maximum System Pressure | 3500 psi |
| Moldboard Width | 12ft in |
| Max Depth Of Cut | 28.3in |
| Side Shift Left | 20.1in |
| Side Shift Right | 26in |
| Blade Pull At Max Weight | 26465lb |
| Blade Down Pressure | 27066.2lb |
| Pump Type | Variable piston |
| Pump Flow | 51gal/min |
| Relief Valve Pressure | 3500psi |
| Circuit Type | Electro-hydraulic closed center, load sensing, |
| Pump Output | 51 gal/min |
| Blade Width | 12ft in |
| Arc Radius | 16.3in |
| Throat Clearance | 4.9in |
| Cutting Edge Width | 6in |
| Cutting Edge Thickness | 0.6in |
| End Bit - Width | 6in |
| End Bit - Thickness | 0.6in |
| Moldboard Height | 24in |
| Moldboard Thickness | 0.9in |
| Blade Pull - Maximum Gvw | 25862lb |
| Blade Pull - Base Gvw | 20830lb |
| Blade Down Pressure - Base Gvw | 17566lb |
| Diameter | 60.2in |
| Shift Left | 25.8in |
| Shift Right | 25.8in |
| Max Reach Outside Tires - Left | 68.6in |
| Max Reach Outside Tires - Right | 75in |
| Max Lift Above Ground | 16.8in |
| Blade Tip Angle - Front | 40degrees |
| Blade Tip Angle - Rear | 5degrees |
| Top Speed - Forward | 27.7mph |
| Top Speed - Reverse | 23.5mph |
| Steering Range - Left/Right | 47.5 degrees |
| Articulation Angle - Left/Right | 20 degrees |
| Forward - 8th | 27.7mph |
| Forward - 7th | 19mph |
| Forward - 6th | 13.8mph |
| Forward - 5th | 10.2mph |
| Forward - 4th | 6.5mph |
| Forward - 3rd | 4.8mph |
| Forward - 2nd | 3.3mph |
| Forward - 1st | 2.4mph |
| Reverse - 6th | 23.5mph |
| Reverse - 5th | 16.1mph |
| Reverse - 4th | 8.6mph |
| Reverse - 3rd | 5.6mph |
| Reverse - 2nd | 3.8mph |
| Reverse - 1st | 2mph |
| Brakes | ISO 3450:1996 |
| Rops/Fops | ISO 3471:1992 / ISO 3449:1992 |
| Sound | ISO 6394:1998 / ISO 6395:1988 |
| Steering | ISO 5010:1992 |
| Cooling System | 10.4gal |
| Engine Oil | 4.1gal |
| Hydraulic System Tank | 16gal |
| Tandem Housing - Each | 16.9gal |
| Circle Drive Housing | 1.8gal |
| Fuel Capacity | 90gal |
| Circle Centershift - Right | 25.8in |
| Circle Centershift - Left | 25.8in |
| Moldboard Sideshift - Right | 26in |
| Moldboard Sideshift - Left | 20.1in |
| Blade Tip Range Forward | 40 degrees |
| Blade Tip Range Backward | 5 degrees |
| Maximum Lift Above Ground | 16.8in |
| Maximum Depth Of Cut | 28.3in |
| Maximum Blade Position Angle | 90 degrees |
| Rear - Scarifier Shank Holders | 9 |
| Mid, V-Type - Working Width | 46.6in |
| Rear - Working Width | 91in |
| Rear - Scarifying Depth, Maximum | 10.5in |
| Mid, Straight - Working Width | 71in |
| Height | 19.8in |
| Width | 6.8in |
| Sidewall Thickness - Inner | 0.5in |
| Sidewall Thickness - Outer | 0.6in |
| Drive Chain Pitch | 1.8in |
| Wheel Axle Spacing | 59.5in |
| Tandem Oscillation - Front Up | 15 degrees |
| Tandem Oscillation - Front Down | 25 degrees |
