| Overall Length | 34.7ft in |
|---|---|
| Clearance | 1.28ft in |
| Front Tyre To Rear Bumper | 30.21ft in |
| Height: Low Profile Cab | 10.5ft in |
| Maximum Steering Range | 49degrees |
| Minimum Turning Radius | 24.28ft in |
| Ripper Beam Width | 7.57ft in |
| Steering Articulation Angle | 25degrees |
| Tandem Wheelbase | 5ft in |
| Track Gauge | 7.11ft in |
| Width Of Moldboard (Optional) | 12.18ft in |
| Width Of Moldboard (Standard) | 14.18ft in |
| Width Of Tyres | 8.54ft in |
| Side Wall Thickness: Inner | 0.1ft in |
| Side Wall Thickness: Outer | 0.1ft in |
| Wheel Axle Spacing | 5.1ft in |
| Tandem Oscillation | 11° forward, 13 ° reverse |
| Drawbar Frame | 210 x 25 mm |
| Ripper Penetration Force | 20232.9lb |
| Ripper Pry Out Force | 28685.7lb |
| Number Of Cylinders | 6 |
| Piston Displacement | 408.3cu in |
| Engine Model | KOMATSU SAA6D107E-1 |
| Front Frame Structure - Width | 1ft in |
| Engine Type | Water-cooled, 4-cycle, direct injection |
| Net Power | 218.6hp |
| Gross Power | 221.3hp |
| Air Cleaner | 2-stage, dry-type |
| Max Torque | 694.1lb ft |
| Battery | 2, low maintenance plus, 12 volt, 1146 cca |
| Fan Speed | Max. 1500 rpm |
| Electrical | 24 volt with 90 amp alternator |
| Torque Rise | 31% |
| Bore | 4.3in |
| Stroke | 4.9in |
| Aspiration | Turbocharged and air to air aftercooled |
| Fuel Tank - Diesel | 109.9gal |
| Cooling System | 6.6gal |
| Transmission | 11.9gal |
| Final Drive | 4.5gal |
| Tandem Housing | 15.1gal |
| Hydraulic System | 18.3gal |
| Circle Reverse Housing | 1.9gal |
| Crankcase | 6.2gal |
| Blade Down Pressure | 19665.3lb |
| Blade Pull | 26091.8lb |
| Total Operating Weight | 40829.7lb |
| Wheel Lean | 20degrees |
| Oscillation - Total | 32degrees |
| Ground Clearance | 2.1ft in |
| Front Axle Type | Solid bar construction welded steel sections |
| Moldboard Side Shift Right | 2.7ft in |
| Standby Pressure | 500psi |
| Moldboard Side Shift Left | 2.7ft in |
| Maximum System Pressure | 3000psi |
| Output | 52.9gal/min |
| Maximum Lift Above Ground | 1.6ft in |
| Maximum Cutting Depth | 2.1ft in |
| Maximum Blade Angle | 90degrees |
| Blade Tip Angle | 40 ° forward, 5 ° backward |
| Circle Center Shift Right | 2ft in |
| Circle Center Shift Left | 1.9ft in |
| Blade Length | 12.2ft in |
| Moldboard Width | 12.2ft in |
| Moldboard Height | 25.4in |
| Moldboard Thickness | 0.9in |
| Cutting Edge | 152 x 16 mm |
| Arc Radius | 1.1ft in |
| Diameter | 60.3in |
