| Overall Length | 32.68ft in |
|---|---|
| Width Over Tires | 10.16ft in |
| Wheelbase | 22.92ft in |
| Rear Ground Clearance | 1.33ft in |
| Tandem Axle Wheelbase | 6.04ft in |
| Front Ground Clearance | 2.26ft in |
| Blade Base | 10.07ft in |
| Height To Top Of Isomount Cab | 12.15ft in |
| Length - Between Tandem Axles | 72.5in |
| Height - Top Of Cylinders | 121.6in |
| Height - Top Of Cab | 12.15ft in |
| Height - Front Axle Center | 27.1in |
| Height - Exhaust Stack | 134.1in |
| Width - Outside Front Tires | 121.9in |
| Width - Outside Rear Tires | 121.9in |
| Width - Tire Center Lines | 98.8in |
| Ground Clearance - Rear Axle | 16in |
| Pry-Out Force | 33788lb |
| Ripping Depth - Maximum | 17.8in |
| Ripper Shank Holders | 7 |
| Penetration Force | 22140lb |
| Shank Holder Spacing - Minimum | 17.5in |
| Shank Holder Spacing - Maximum | 20in |
| Number Of Cylinders | 6 |
| Net Power Gear 4-6 | 312hp |
| Engine Make | 2236 |
| Net Power Gear 1-2 | 302hp |
| Power Measured @ | 2000rpm |
| Net Power Gear 5-6 | 312hp |
| Max Power | 312hp |
| Net Power Gears 7-8 | 312hp |
| Net Torque Gears 7-8 | 1261.3lb ft |
| Displacement | 763cu in |
| Bore | 5.1in |
| Stroke | 6.2in |
| Engine Model | Cat C13 ACERT VHP |
| Derating Altitude | 15000ft in |
| Maximum Torque | 1261lb ft |
| Speed At Rated Power | 2000 RPM |
| High - Ambient Capability | 122degrees |
| Circle - Diameter | 71.8in |
| Drawbar - Height | 8in |
| Front Axle - Height To Center | 27.1in |
| Circle - Blade Beam Thickness | 2in |
| Base Power (All Gears) - Net | 297hp |
| Standard - Fan Speed - Maximum | 1200 RPM |
| Standard - Fan Speed - Minimum | 550 RPM |
| Standard - Ambient Capability | 109degrees |
| Std Operation Weight - Total | 57452lb |
| Max Operation Weight - Total | 78643lb |
| Cooling System Fluid Capacity | 12.3gal |
| Circle Gearbox Fluid Capacity | 2.1gal |
| Tire Size | 18.00-25 12PR (G-2) |
| Brakes - Parking | Spring applied, hydraulically released |
| Brakes - Service | Oil-actuated, oil-disc |
| Transmission | Direct drive, power shift, countershaft |
| Forward/Reverse Gears | 8 Fwd/6 Rev |
| Brakes - Secondary | Oil-actuated, oil-disc |
| Brakes - Service - Surface Area | 7724in2 |
| Articulation Angle | 20degrees |
| Turning Radius | 29.2ft in |
| Transmission Type | direct drive, power shift, countershaft |
| Number Of Gears - Forward | 8 |
| Number Of Gears - Reverse | 6 |
| Max Speed - Forward | 33.5mph |
| Max Speed - Reverse | 26.5mph |
| Wheel Lean | 18.2degrees |
| Oscillation - Total | 32degrees |
| Ground Clearance | 2.3ft in |
| Standby Pressure | 450 psi |
| Maximum System Pressure | 3500 psi |
| Moldboard Width | 16ft in |
| Max Depth Of Cut | 19.2in |
| Side Shift Left | 25.6in |
| Side Shift Right | 43.1in |
| Blade Pull At Max Weight | 49156lb |
| Blade Down Pressure | 42957.1lb |
| Pump Type | Variable piston |
| Pump Flow | 74gal/min |
| Relief Valve Pressure | 3500psi |
| Circuit Type | Electro-hydraulic load sensing, closed center |
| Pump Output | 74 gal/min |
| Reservoir Tank Capacity | 17.2gal |
| Blade Width | 16ft in |
| Arc Radius | 16.3in |
| Throat Clearance | 4.9in |
| Cutting Edge Width | 8in |
| Cutting Edge Thickness | 1in |
| End Bit - Width | 6in |
| End Bit - Thickness | 0.8in |
| Moldboard Height | 31in |
| Moldboard Thickness | 1in |
| Blade Pull - Base Gvw - Awd | 38781lb |
| Blade Pull - Maximum Gvw | 48554lb |
| Diameter | 71.8in |
| Shift Left | 25.5in |
| Shift Right | 23.5in |
| Max Reach Outside Tires - Left | 90in |
| Max Reach Outside Tires - Right | 101.9in |
| Max Lift Above Ground | 15.6in |
| Blade Tip Angle - Front | 40degrees |
| Blade Tip Angle - Rear | 5degrees |
| Top Speed - Forward | 33.5mph |
| Top Speed - Reverse | 26.5mph |
| Steering Range - Left/Right | 47.5 degrees |
| Articulation Angle - Left/Right | 20 degrees |
| Forward - 8th | 33.5mph |
| Forward - 7th | 23mph |
| Forward - 6th | 16.7mph |
| Forward - 5th | 12mph |
| Forward - 4th | 7.7mph |
| Forward - 3rd | 5.6mph |
| Forward - 2nd | 3.9mph |
| Forward - 1st | 2.8mph |
| Reverse - 6th | 26.5mph |
| Reverse - 5th | 18.2mph |
| Reverse - 4th | 9.5mph |
| Reverse - 3rd | 6.1mph |
| Reverse - 2nd | 4.2mph |
| Reverse - 1st | 2.2mph |
| Cooling System | 12.3gal |
| Hydraulic System - Total | 30.1gal |
| Engine Oil | 7.9gal |
| Hydraulic System Tank | 17.2gal |
| Tandem Housing - Each | 32.1gal |
| Circle Drive Housing | 2.1gal |
| Fuel Capacity | 130gal |
| Circle Centershift - Right | 23.5in |
| Circle Centershift - Left | 25.5in |
| Moldboard Sideshift - Right | 43.1in |
| Moldboard Sideshift - Left | 25.6in |
| Blade Tip Range Forward | 40 degrees |
| Blade Tip Range Backward | 5 degrees |
| Maximum Lift Above Ground | 15.6in |
| Maximum Depth Of Cut | 19.2in |
| Maximum Blade Position Angle | 65 degrees |
| Height | 25.5in |
| Width | 9.3in |
| Sidewall Thickness - Inner | 0.9in |
| Sidewall Thickness - Outer | 0.9in |
| Drive Chain Pitch | 2.5in |
| Wheel Axle Spacing | 72.5in |
| Tandem Oscillation - Front Up | 15 degrees |
| Tandem Oscillation - Front Down | 25 degrees |
